EPA #SWMM5 Build 5.1.012 (03/14/17) Updates

SWMM 5.1 Update History
=======================
https://www.epa.gov/water-research/storm-water-management-model-swmm#downloads
------------------------
Build 5.1.012 (03/14/17)
------------------------

Engine Updates:

1.  The direct.h header is now only #included in the swmm5.c file when
    compiled for Windows. (swmm5.c)

2.  Engine Update #7 in Build 5.1.011 (internally aligning the wet time
    step with the reporting time step) was redacted since it caused
    problems for certain combinations of time steps. (runoff.c)

3.  A subcatchment's bottom elevation is now used instead its parent
    aquifer's value when saving a water table value to the binary results
    file. (subcatch.c)

4.  A bug that failed to limit surface inflitration into a saturated rain
    garden LID unit was fixed. (lidproc.c)

5.  Calculation of the maximum limit on LID drain flows was modified to
    produce smoother results at low depths above the drain offset.
    (lidproc.c)

6.  A variable used for reporting detailed LID results is now properly
    initialized. (lid.c & lid.h)

7.  The occasional writing of duplicate lines to the detailed LID results
    file was fixed. (lidproc.c)

8.  The conversion from conduit seepage rate per unit area to rate per unit
    of length was changed to use top width instead of wetted perimeter since
    only vertical seepage is assumed to occur. (link.c)

9.  The coefficient of the evaporation/seepage term in the dynamic wave
    equation for updating conduit flow was corrected (from 1.5 to 2.5).
    (dwflow.c)

10. The Engels flow equation for side flow weirs was corrected (the original
    equation used in SWMM 3 & 4 was incorrect). (link.c)

11. Crest length reductions for end contractions are no longer used for
    trapezoidal weirs. (link.c)

12. The Slope Correction Factor for culverts with mitered inlets was corrected.
    (culvert.c)

13. An entry in the table of gravel roadway weir coefficients was corrected.
    (roadway.c)

14. The user supplied minimum slope option is now initialized to 0.0
    (meaning none is provided). (project.c)

15. NO/YES are no longer accepted as attributes for the NORMAL_FLOW_LIMITED
    dynamic wave simulation option (only SLOPE/FROUDE/BOTH are valid).
    (project.c)

16. Changes were made so that the Routing Events and Skip Steady Flow
    options work correctly together. (routing.c & globals.h)

17. Steady state periods with no flow routing no longer contribute to the
    routing time step statistics. (stats.c and report.c)

18. When compiling statistics on the frequency of full conduit flow the
    number of barrels is now accounted for. (stats.c)

19. Under kinematic wave or steady flow routing, the water level in
    storage nodes that have no outflow links is now updated correctly
    over time. (flowrout.c) 

20. The formula for the depth at maximum width for the Modified Basket Handle
    cross section was corrected. (xsect.c)


GUI Updates:

1.  Profile plots now correctly update the main and axis title text when
    changed via the Profile Plot Options dialog. Also the downstream
    offset height of non-conduit links is set to 0 on the plot.

2.  The LID Control Editor now sets the Storage Layer Thickness to 0 when
    a Rain Garden is selected as the type of LID being edited.

3.  An OnChange event handler was added to each of the LID Control Editor's
    data fields to record when a value is changed.

Comments

Popular posts from this blog

World-Renowned Urban Drainage Modeling Authority Robert Dickinson Joined Innovyze in January, 2008

SWMM 5 Error Messages

New Warning Messages in SWMM 5.0.014 to 5.0.016